37 real-world robotic mower question themes.
Diagnose My MowerStop and isolate the mower, then inspect the body/cover and collision-sensor movement for anything jammed, displaced or damaged. Restart only after the body moves freely. If the collision warning persists with no obstruc
Read answer →Keep the installation within the model/manual limits. Husqvarna currently states a maximum total loop-wire length of 800 m for Support by Wire installations; older/model-specific guide-loop limits can differ, so check th
Read answer →They can work in partly obstructed gardens, but reliable satellite positioning still matters. Keep the docking point in good satellite view and use EPOS Support by Wire where a supported model has weak-signal lawn areas.
Read answer →Confirm both batteries are the correct variants for the mower article number, fully charge the mower, and compare runtime with its normal history. If the mower still reports abnormal battery behaviour, have battery diagn
Read answer →Start with the exact installation manual for the mower. Keep boundary clearances from walls, slopes and obstacles, create islands in the correct direction, and route the guide wire so the mower has a clear corridor back
Read answer →The exact minimum is installation- and model-specific. Do not guess: use the model's installation manual and required corridor clearances. If a passage is too narrow, the mower can struggle to navigate or damage the lawn
Read answer →First improve sky view at the docking point/reference setup and update mower firmware. For compatible models, Husqvarna's Support by Wire can cover weak-satellite areas inside existing virtual boundaries, but it does not
Read answer →Record the firmware version and exact errors, check station power/contacts and docking path, and avoid replacing more parts until the fault is isolated. If the problem began immediately after an update and persists after
Read answer →Use the charging-station LED before condemning the PCB. A solid red LED can indicate a power-supply or charging-station-board failure; no light points first to outlet, power supply or low-voltage cable. Husqvarna recomme
Read answer →NERA identifies the mower platform/generation; EPOS is Husqvarna's satellite-based virtual-boundary system used with compatible NERA models. A NERA mower may be configured with physical wire or, where supported and equip
Read answer →Choose around the site rather than brand alone: lawn size, tree/building satellite blockage, slopes, narrow passages, local dealer support, wire vs wire-free preference, and service access. Husqvarna offers physical-wire
Read answer →Check both area capacity and cutting-height range against the lawn. Dense, high-cut turf increases load, so the mower should not be selected on area alone. Confirm the exact R4 cutting-height specification and gradually
Read answer →On Navimow H1, Segway says a red charging-station light means no communication between mower and station. Make sure the mower is powered on and properly docked. If the red light remains while correctly connected, contact
Read answer →Normal parked/standby behaviour is controlled by the mower's firmware and power-management design; users should not force power-off routines that conflict with scheduled operation. Use the current i-series manual/app beh
Read answer →Check for a newer firmware/app release, confirm the map and positioning are healthy, and test a fresh task in an open area. If the behaviour started directly after an update and remains repeatable, report the firmware ve
Read answer →Check satellite/RTK conditions before purchase. Mammotion recommends good open-sky view for both mower and RTK station, and advises extra care around tall walls, trees and narrow lanes. Use the app/signal checks and map
Read answer →Use the task/perimeter settings available for the installed firmware. Mammotion firmware has added and refined perimeter/no-go-zone border mowing options over time, so first update firmware and check Task Settings rather
Read answer →Check obstacle-avoidance and boundary settings, then update firmware. Mammotion release notes show ongoing changes to perimeter mowing, map-border accuracy and obstacle behaviour, so an edge offset can be software/settin
Read answer →Use only Mammotion-supported remote-control/app functions. Third-party hubs may not provide the safety, authentication or range behaviour expected by the mower. For moving between disconnected areas, use supported channe
Read answer →Runtime varies with grass height, slope, temperature, cutting load and route efficiency. Use the mower's own task history as the baseline and investigate a sharp decline rather than comparing a single cycle with another
Read answer →Real mowing time depends on terrain, grass load, pattern, turns and battery condition. Compare repeated cycles on the same lawn and look for abnormal decline. Treat advertised capacity/range as planning information, not
Read answer →Use only charging-limit or smart-charging controls actually exposed in the Mammotion app/firmware. Mammotion has added preferred recharge/return-to-work and Smart Charging features on newer firmware, so availability depe
Read answer →LED meanings are model-specific. If charging and scheduled operation are normal, first check the current LUBA manual/support page before treating a flashing light as a fault. If charging, docking or communications are al
Read answer →Use the app's mapped work areas plus supported channels/routes between them. Current Mammotion firmware supports separate-lawn mapping and channel/no-go-zone editing on supported models; update first, then create safe ro
Read answer →Fully charge the battery, clean/check charging contacts, verify the correct battery pack is fitted, and compare runtime in light mowing conditions. If runtime remains dramatically below its previous normal level, battery
Read answer →Confirm that the work area is correctly mapped/assigned and that the mower has positioning/data connectivity. Kress RTKn depends on satellite positioning plus correction data; if mapping is correct but the task never ent
Read answer →Use the firmware-update method specified for the exact Mission model and manual. Do not use an arbitrary firmware file: model families differ. If the app/manual does not provide a USB procedure for that mower, contact Kr
Read answer →First document the exact location, firmware version and whether positioning is obstructed there. Kress RTKn can use dead reckoning during temporary satellite obstruction, but repeated boundary deviation after an update s
Read answer →Check lawn size, narrow passages, slopes, wire-installation complexity, local dealer support and whether you prefer a physical-wire system or Kress RTKn. A wired model can be a good fit where satellite positioning is dif
Read answer →Match the mower to lawn area, slope, obstacle complexity and connectivity. Kress currently offers wired Mission, RTKn and EyePilot/RTKn families with different capacities and features. Choose with headroom rather than se
Read answer →Before long storage, fully charge the iMOW battery, clean the mower and store it dry and frost-protected. STIHL warns that insufficient charge during storage can lead to deep discharge. Recommission by reconnecting the d
Read answer →Compare terrain, satellite visibility, slope, dealer network and service preference. LUBA uses RTK/vision mapping and needs suitable positioning conditions; iMOW has a strong dealer/service ecosystem and model-specific w
Read answer →Both are physical-wire robotic mower families, but capacities/features vary by exact model. GARDENA publishes separate installation guidance for minimo and city/life, including boundary and guide-wire setup. Compare lawn
Read answer →LED meanings differ by Ambrogio model, so use the exact model manual before diagnosing by colour alone. If the mower does not charge or the light changes unexpectedly, first verify station power, clean contacts and corre
Read answer →Check Wi-Fi signal strength at the charging station, router band/compatibility, app/firmware updates and whether the mower reconnects when moved away from the dock. If the failure is consistently tied to docking with str
Read answer →Use the charging-station placement clearances in the A2 manual and make sure the mower has a safe mapped route between the dock and mowing area. A hard surface beside the lawn can work only if placement, approach path an
Read answer →Start with area capacity and positioning suitability, then integration. RTK/GNSS systems need reliable correction data and enough sky view; vision/LiDAR systems have different site constraints. Treat Home Assistant integ
Read answer →Use MowerFix AI to work through the checks for your exact mower before ordering parts.
Diagnose My MowerFull access is included with the €4.99 one-time MowerFixAI lifetime access.